The summertime shower on the dacha plot is considered the No. 2 construction, as the very first in importance is the outside toilet. At first glance, this simple construction has nothing complex, but this a trifle as the selection and installation of a plastic container for the shower at the dacha will bring a whole lot of trouble. The way to manage all these nuances by themselves, we’ll now attempt to comprehend. Without or with heating

Before you opt for a tank for the shower at the country must decide on its performance. On if this plastic container is going to be equipped with heating system, depends on the comfort of bathing.

• Multifunctional and convenient to use would be a heated shower tank, even functioning on power. Obviously, and without linking to electricity this tank may be used, however in this is actually the relaxation of taking water procedures. If the sun did not have sufficient time to warm water, then this problem can easily be solved with power. It’s convenient to put in a tank with heating system, if the shower will be utilised in early spring and late fall. Hot summertime, the water in the tank will be heated by sunlight, so during this period, the heating is simply not included.
• A vinyl tank without heating is a normal tank, such as a cone mounted onto the roof of a bathtub home. The water from the tank is heated from the sun. That is, if the weather is wet and muddy, it is possible to take only a refreshing shower or deny to bathe in any way. Tanks without heating is appropriate to spend the event the cottage is seen very infrequently, and then only in summertime.

The primary difference between these tanks just installed heating element. Size, quantity, and colour of this product can be quite different. It is essential that any chosen tank had a broad neck, simple to pour water and was firmly attached to the roof of the shower toolbuild.ru home.

Tip: Flat black aquariums are more powerful. A large area of a thin layer of water will be heated faster by the sun. Dark walls of the tank draw the sun’s rays, plus the water within the tank does not bloom.

Design features of plastic shower tanks

Plastic shower tanks such as summer homes are especially popular with consumers for several reasons;

• A unique composition of plastic is employed to generate the tanks, which increases the product’s lifespan for 30-50 years. At precisely the same period, plastic tanks for summer showers are distinguished by a moderate cost, light weight and simplicity of setup.
• Flat square-shaped tanks are best for covering outdoor shower houses rather than a roof. All you need to do is build the shower box, and repair the tank on top instead of the roof.
• In the production of shower tanks, so many manufacturers use food-grade polyethylene, which does not degrade from exposure to UV rays. Environmentally friendly material ensures that the safety of water during long-term storage. Plastic does not corrode under most circumstances, which cannot be said about alloy.

When choosing a plastic tank should know that the tanks without electric heating most often are made in volume by 100 to 200 liters. Round heated tanks are made in the form of drums using a volume of 50 to 130 liters of water. Flat heated tanks are often designed for 200 gallons of liquid. In any design, water is poured in buckets via a broad neck or from pump.

Rarely does anybody in the dacha construct a capital shower made of brick or cinder block. Normally its usage is limited to three summertime and then during the planting of the vegetable garden, in addition to harvesting. For such a short period it is sufficient to construct a light cottage out of any sheet material. Not a bad choice is a shower for dacha from polycarbonate with a changing room, which is not difficult to design and create yourself. Why it is better to choose polycarbonate for liner the shower

Polycarbonate is not the only material to get a dacha shower. For this particular case with success will match exactly the profiled sheeting or batten. Just today we decided to stop just with this gorgeous and durable stuff.

Let’s consider the advantage of using polycarbonate for cladding the shower along with other similar substances:

• In the event the advantages of polycarbonate have convinced you, let us proceed to the next phase of building a shower for dacha.
• A few important tips about the development of the design of a country shower using a changing room

Such a simple structure, as a bathtub out of polycarbonate for dacha requires the development of the project. It’s not required to develop complex drawings, and also a simple scheme can be sketched out. Here you need to immediately decide for yourself what you need to construct a shower. Very fast you may earn a lightweight stall and just put it on the ground. More complicated in the production of shower to the base with water heating, however, such a design will survive longer. Additionally, in a dacha shower you will be able to bathe in sunlight.

• Structure of a dacha shower begins with determining its place. It’s necessary to mention that the tank should be continuously full of water. Doing this in buckets from afar is embarrassing and difficult. It’s much better to place the shower stall near the water consumption.
• In the event the dacha shower will bathe a whole lot of people, it should be placed as close as possible into this cesspool or septic tank. Close setup dacha bath close to the cesspool will rescue on laying sewer pipes, but it’s desirable not to attract the stall nearer into the accumulator of impurities nearer than 3 m. On warm days, awful smells from the sewer system will permeate the shower, creating an unpleasant atmosphere whilst bathing.
• The water from the tank of a summer shower is heated by the sun. The stall must be put in the sunniest place, where there is no shade in the trees and tall structures.
• Inside the shower stall and altering room from polycarbonate should provide lighting, which means you are able to bathe at night. Only it’s crucial to consider that the lights need to have a high degree of protection against water. It’s optimal to place shower cottages on the back of the home. Here are closest to this sewer, water source and not far to pull on the electrical cable for lighting.
• Decided on the location of the area of this summer shower, start to earn a plot of this cabin itself from polycarbonate. Originally it was determined that the backyard shower will probably be using the changing room. In cases like this, the width of the design will turn out 1 m, and the length – 1,6 m. When the owners are overweight individuals, then the width of the shower cubicle with a locker area is much better to increase 1.2 m.
• Inside the shower stall provide separation. Separate the dressing room threshold, in addition to tarpaulin curtain. They will not enable the water to wet clothes and shoes.
• If desirable, the dressing room can be coordinated from the anteroom. Then, close to the shower enclosure separately install extra racks, to which fix sheets of polycarbonate. The dimensions of this pre-bath is dependent upon the tastes of the owner. Sometimes cottagers build bigger pre-baths at which, along with the dressing area, equip a recreation room. Indoors you will find benches and a table.
• The total height of this shower cottage from ground to roof is at least 2.2 m. Together with the tank it could achieve 2.5 m, and much greater. The elevation within the shower stall will likely be reduced. Part of the space below will have a wooden tray, along with the shirt will probably hang a watering can with a tap less than 15 cm.

Given all these variables, on a bit of paper sketches the scheme of the shower using a polycarbonate dressing room, then proceed into its structure.